濟南祥富飼料機械廠
聯系人：王經理
手機：131-7641-3620
電話：0531-84251890
地址：濟南市濟北開發區國道220線東側徐灣路口
1、飼料攪拌機http://www.rzguanggaowang.com/有軸向裂紋或徑向裂紋現象，導致這種現象的原因是可調質溫度達不到，物料熟化程度較差，應提高調質溫度，增加調質時的蒸汽量；還有一種可能是切刀位置離較遠且鈍，使顆粒被碰短或撕裂而非切斷。
Feed mixer has an axial or radial crack crack phenomenon, the causes of this phenomenon is adjustable mass temperature of less than, less degree of curing material, quenching temperature should be increased, increasing the amount of steam when quenched; there is a may be far away from the cutter location and blunt, the particles being touched or torn rather than cut short.
2、顆粒料長短不一，應調整切刀距離或調整分料偏轉刮位置； 顆粒表面較光滑，但硬度過高，可能是環模壓縮比較大，應降低飼料攪拌機環模壓縮比。
Pellets of varying lengths, the distance should be adjusted or adjusting knife scraping material deflection position; the particle surface is smooth, but the hardness is too high, it may be relatively large ring mold compression should reduce feed mixer ring mold compression ratio.
3、顆粒表面不很光滑，并且粉化率高，可能是飼料攪拌機環模壓縮比較小，應增大壓縮孔、環模壓縮.
The particle surface is not very smooth, and the powder is high, it may be compressed feed mixer ring mold is relatively small, the hole should be increased compression, compression ring mold.
4、顆粒水份偏高時生產產量偏低，并且經常出現堵機現象，可能是減壓閥不能起減壓效果或輸水閥不能起到輸水作用，應調整減壓閥，使進入調質器蒸汽壓力為0.1—0.4MPa，并使輸水閥能起到輸水作用，也可以相應增加調質溫度，因?yàn)闇囟仍龈哂欣谖锪鲜旎鹊奶岣撸话銣囟让可?1℃時物料水份約增加1%。
High water particle production is low yields, and often blocking machine phenomenon, probably can not play decompression valve or water valve can not play the role of water, adjust valves, entering conditioner steam pressure 0.1-0.4MPa,water and water valves can play a role, but also can be a corresponding increase in quenching temperature, because temperature increases will help improve the aging of the material, usually when the temperature is increased by 11 ℃ material moisture an increase of about 1%.